Hi again,
I just updated two of my Volumio boxes to the latest Volumio2 . . . after adjusting the settings I did the last step and added my library as nfs mount.
Okay, it is around 1TB . . . .
The boxes seems to start the update but then the even disappear from the network. The WebUI shows the circling balls and that’s it so far. No answer to ping . . . I tend to leave them alone for the night.
I am not exactly sure which Raspi Models I have there, I believe one is a Model B the other a B+.
Of course I cannot access them with ssh even if I try . . . there is no network connection.
Is it possible that the update uses all the resources the poor Raspi can provide
ok. . .update: the WebUI now crashed/disappeared with the expected "host unreachable "message.
I modified the “library” to one folder/album only . . . same issue, after some time the connection just seem to collapse
Update:
I changed the mount to cifs now, as the nfs it mounts ( somehow) but when attempting to read the data Volumio dies . . . it seems that the connection stays for quite some time but then of course the ssh is closed as well.
Both Raspi boxes are connected to 100MBPS LAN . . .
The Raspi LEDs still show that there might be some activity but . . . .
Any ideas ?
Issue #777 is a different problem, not related to what Torsten reported.
The alignment issue happens on armv7 (non-PI platforms) only and is being fixed right now.
Would it be possible for you to look at the journal logs (sudo journalctl -b) and see if there are any reported problems. Alternatively, you can send the logs via the “dev” interface to the Volumio UI (192.168.x.xx/dev), including your username for reference.
jepp I will setup another box to get the log. Not quite understood what the “dev” interface actually is but I am sure I will figure it out once I have the Volumio2 installed again. ( I moved back to 1.55 for now … since no music is not a solution )
My NAS is detected and I added the library path. Than it scan it…(not a very big library)…Once finished scanning it collapses with turning icon wheel. When I refresh the browser it says “no connection” and I have to reboot Cubox.
Hi Daniel,
you probably have the above mentioned issue #777, which you can confirm when you are able to ssh into your cubox and do
sudo journalctl -f
before you start scanning. When you look at the logfile, chances are that you will will find an error “Alignment fault”.
In that case, the issue has been fixed and you need to wait a few days as we are generating a new cubox Image.
Well, I didn’t figure it out to be honest.
I wanted to attach a log here instead but I was not allowed ( the extension blablabla is not allowed )
So how do I do this ?
There is an option to upload attachments on the forum (at bottom of reply), but I don’t know what limitations there are. You can cut and paste text as an alternative.
(The “dev” log thing is very simple, but perhaps I wasn’t clear enough. Enter your normal IP address for Volumio, and add “/dev” to the end of it. This will take you to a page with various things, one of which is “Send a log”).
I was on the “dev” page but it is not transparent to see what I am actually sending . . .actually I did it and sent a log twice, not sure if it was a sufficient one.
Uploading an attachment failed since it constantly complained about extensions ( tried txt, log, none, and even no extension )
Copy paste is of course an option but then I would need to select prior to do this otherwise it will reach the limitations of the message body.
As of now after starting to populate the library the box is again hanging an unreachable I watched it with journalctl -f
it stopped for a while and then came back
Apr 03 14:52:58 volumio kernel: smsc95xx 1-1.1:1.0 eth0: kevent 2 may have been dropped
Apr 03 14:52:58 volumio kernel: CIFS VFS: Server HOSTSERVER has not responded in 120 seconds. Reconnecting...
Apr 03 14:52:52 volumio mpd[517]: client: [1] closed
Apr 03 14:52:53 volumio mpd[517]: client: [4] opened from ::ffff:127.0.0.1:38288
Apr 03 14:52:56 volumio mpd[517]: update: added NAS/Musik/Sukru Tunar/Bir Muhabbet Kusu.mp3
Apr 03 14:52:56 volumio mpd[517]: update: added NAS/Musik/João Gilberto/O amor, o sorriso e a flor/04 João Gilberto - Trevo de quatro folhas.mp3
Apr 03 14:52:56 volumio mpd[517]: update: added NAS/Musik/João Gilberto/O amor, o sorriso e a flor/09 João Gilberto - Corcovado.mp3
Apr 03 14:52:56 volumio mpd[517]: update: added NAS/Musik/João Gilberto/O amor, o sorriso e a flor/11 João Gilberto - Amor certinho.mp3
Apr 03 14:52:57 volumio mpd[517]: update: added NAS/Musik/João Gilberto/O amor, o sorriso e a flor/03 João Gilberto - Só em teus braços.mp3
Apr 03 14:52:57 volumio mpd[517]: update: added NAS/Musik/João Gilberto/O amor, o sorriso e a flor/10 João Gilberto - Discussão.mp3
Apr 03 14:52:57 volumio mpd[517]: update: added NAS/Musik/João Gilberto/O amor, o sorriso e a flor/06 João Gilberto - Um abraço no bonfá.mp3
Apr 03 14:52:57 volumio mpd[517]: update: added NAS/Musik/João Gilberto/Desafinado/19 Outra vez.mp3
Apr 03 14:52:57 volumio mpd[517]: update: added NAS/Musik/João Gilberto/Desafinado/10 Manhã de Carnaval.mp3
Apr 03 14:52:58 volumio mpd[517]: update: added NAS/Musik/João Gilberto/Desafinado/04 Meditação.mp3
Apr 03 14:52:58 volumio mpd[517]: update: added NAS/Musik/João Gilberto/Desafinado/02 Você e eu.mp3
Apr 03 14:52:59 volumio mpd[517]: update: added NAS/Musik/João Gilberto/Desafinado/11 O amor em paz.mp3
Apr 03 14:52:59 volumio mpd[517]: update: added NAS/Musik/João Gilberto/Desafinado/05 Samba de uma nota só.mp3
Apr 03 14:52:59 volumio mpd[517]: update: added NAS/Musik/João Gilberto/Desafinado/12 O barquinho.mp3
Apr 03 14:52:52 volumio systemd[1]: systemd-logind.service watchdog timeout (limit 1min)!
Apr 03 14:52:53 vol
Then it continued to read some more folders . . . and ends with “broken pipe” error message on ssh . . . once the connection is dead like this I have to restart the device
From your uploaded logs the problem appears to occur without library scanning. You say you have tried it on more than one RPi, but I presume that is the same image. Can you download a fresh image & check it’s md5sum before flashing? Make sure that you leave the RPi alone for 10 mins on first boot.
you are right both got the same image.
I now downloaded it again and flashed again ( after checking MD5) the result is the same . . .
What I did now in addition I started
sudo journactl -f > logfile
So now I have at least a huge log . . . how would I be able to upload it here ( the upload function does not allow me )
cheers
Torsten
BTW: Could it be that there is an issue with character coding in file or folder names? I do have quite some tracks in kyrillic and some with spanish characters.
(1) confirm that you downloaded the Volumio software from here;
confirmed
(2) give details of how you flashed the image to the sd card, and the sd card size;
I used the etcher tool on my Linux computer to flash three different 8GB cards unfortunately all are same brand SanDisk Ultra
(3) post the result of typing ‘cat /proc/cpuinfo’ from an ssh session.
Volumio Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
volumio@volumio:~$ cat /proc/cpuinfo
processor : 0
model name : ARMv6-compatible processor rev 7 (v6l)
BogoMIPS : 697.95
Features : half thumb fastmult vfp edsp java tls
CPU implementer : 0x41
CPU architecture: 7
CPU variant : 0x0
CPU part : 0xb76
CPU revision : 7
Hardware : BCM2708
Revision : 0002
Serial : 000000006495fa04
Volumio Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
volumio@volumio:~$ cat /proc/cpuinfo
processor : 0
model name : ARMv6-compatible processor rev 7 (v6l)
BogoMIPS : 697.95
Features : half thumb fastmult vfp edsp java tls
CPU implementer : 0x41
CPU architecture: 7
CPU variant : 0x0
CPU part : 0xb76
CPU revision : 7
Hardware : BCM2708
Revision : 0002
Serial : 000000006495fa04
Well, I flashed the same card with the same image but . . . used Ubuntu imagewriter now.
So far after booting a while ago and updating the library now . . .the system is still alive, even when I see a lot of error messages and it hangs from time to time . . . it is still populating the library
Ah ok, it becomes clearer. The RPi that you reported the cpuinfo for only has 256MB of RAM. Volumio needs a minimum of 512MB to run properly. Good excuse for an upgrade ??